Blog

Total Water Heater Maintenance Tasks

Posted by on Jun 12, 2015 in Gas Water Heater Repair Carrollton TX, Water Heater Repair Carrollton TX, Water Heater Use and Care | 0 comments

Water Heater Repair Carrollton TX is not about to discuss the unlucky reports concerning water heater maintenance of “getting up to the freezing bath,” here. In addition, we shall presume that one knows the straightforward notion of ensuring ones water heater is maintained routinely in an effort to receive the most from its expected life. This can help one reduce costs on power costs as well. All of that is reasonable we understand. Though hot water heaters do not require a lot with regard to maintenance (and we are astounded, even though not shocked, by the amount of customers we come across who haven’t executed anything to their water heater), following are the responsibilities individuals must keep in mind with regards to routine maintenance.

How Long Should My Carrollton TX Water Heater Last?

The common gas water heater lasts 8 to 10 years. There are numerous things which may have an affect on the all around life expectancy needless to say, however this is an effective standard. Almost certainly the greatest factor that can influence the long life of it is normally mineral deposits. A lot of of the steps in this article should go a long way in assisting to lower the accumulation of mineral deposits within the storage tank of the water heater.

Carrollton Water Heater Repair PreventionHot Water Heater Repair Carrollton TX

House owners, even people which usually do not feel extremely handy, are capable of doing lots of water heater care by themselves. Although usually, water heaters are safe and sound, it is crucial to bear in mind that they actually do work from electric power and/or gas, for that reason correct safety techniques have to be taken. Be sure to implement all these measures as an instructional tutorial, for we’d much rather discuss all these together with you directly. The electrical power to the water heater requires to be switched off ahead of carrying out any routine maintenance. Ones breaker box ought to have a preferably labeled switch to point out which breaker is the heater’s. With a gas heater, move the gas cutoff counterclockwise to shut off the gas to the heater.

The portion of the heater that aids with avoiding rusting inside of the water storage tank are the anode rods, or additionally named sacrificial anode rods. Nearly all are made from aluminum or magnesium around a steel wire. In time the external covering of the rods will erode and they really should be replaced when the steel wire is noticeable. They typically last around 5 years, though that may be reduced if ones water is soft. In time, it is better and less costly to have the anode rods changed, so that one can acquire an extended life from the water heater storage tank. The rods should really be looked at on an annual basis.

The follow video does a very good job of demonstrating the method needed with replacing the anode rods:

Not every water heater has dip tubes. They must be reviewed for deterioration every 6 months. To evaluate it, take it out and evaluate its length to the height of the water heater. It needs to be around 6″ to 8″ shorter compared to the tank. Whenever it’s smaller than that, or simply displays clues of breakage or falling apart, it’ll need to get changed.

The big and small flush. Once more, mineral deposits are the major reason of water heater malfunctions. Based on the level of quality of water in ones residence will establish exactly how rapidly sediment will establish inside of the storage tank. This sediment can solidify in time, creating unusual popping sounds from the storage tank, decrease the effectiveness of the water heater, and perhaps clog up the drain valve. If possible, every 6 months, but at the least every year, empty 1 or 2 gallons of water from the drain valve in the bottom of the hot water heater in a pail or by a hose in a container outside the house. Look to determine the amount of sediment is within the pail after the water settles. If it seems pretty clear, that great! When these kinds of small flushes are undertaken 2 times yearly, one may well not need to complete a big flush as frequently. If the water seems to be very dirty, a full flush should really be conducted. It is likewise a very good occasion to ensure the bottom drain valve of the storage tank is functioning properly and not leaking. Most are ordinarily composed of plastic and with time when they aren’t opened up, they may get stuck or not close up firmly, so opening and closing them in the course of the small flush test is very good.

There can be unique measures one could take while flushing to deal with any specific water smells which could happen when hot water comes from faucets within the residence also.

This video illustrates exactly how and advantages for a water heater flush:

Regarding holiday or temporary houses, one will need to empty the storage tank of all its water in order to avoid any kind of flooding when the dwelling is not being occupied. Naturally, make certain to fill it up while the residence is to be resided in once again.

Water pipe inspection. Look to ensure all water piping have no leaks or are impaired at all. This should be straightforward to see when there are any leaks with any piece of the water plumbing or storage tank for it will have water below and/or near the device. Leaking water may cause water damage to areas of ones house, so ensure all seems dry, primarily if the heater is within the property and not in a garage.Carrollton Water Heater Repair

T&P valve assessment. The T&P valve, also known as the temperature and pressure relief valve, must be looked at annually. The goal of the T&P valve would be to preserve the water heater storage tank from extra pressure, and exploding, not to frighten everyone. The owners handbook must be looked over to be sure the correct techniques are used but listed here are the fundamental actions. A little water may come out of the valve and it will probably be really hot so use caution. Raise the handle and let go of it. Have a container available to catch any extra water that can come out. When the handle is lifted, the noise of pressure getting discharged will be noticed. The handle will need to snap back into position. In the event that it won’t give it a try once more. In case it will not go back again into position following a number of attempts, it is going to have to be changed. The valve may possibly drip a little water after doing that for a short period of time. If it fails to discontinue dripping after a couple of hours contact us.

There does exist a lot of discussion on what the ideal temperature setting really should be. The manufacturer pre-programmed setting is in most cases 140 degrees, which is indeed warmer than almost all people definitely will ever have to have. 120 degrees is the common temperature and a number of people also go as far as 100 degrees. We’ll be publishing much more on this subject in the near future, but we highly recommend not going over 120 degrees.

Just For Gas Water HeatersWater Heater Repair Carrollton TX

The gas venting system requires being checked out each 3 months. Examine to guarantee all fittings are tight and for obstructions and harm to the vent pipes along with making certain they’re absolutely free of rust and deterioration .. Gas fired hot water heaters vent fumes to the outdoors of the house. If these fumes flow within the dwelling it might be deadly and a fire threat. Ensure everything combustible or corrosive is faraway from the exhaust ventilation to alleviate problems with fires. Change all loose, broken or corroded areas of vent pipes.

Examine the pilot light to do a visual test of the way it is working. The pilot light is the element that ignites the gas burner that will heat the water. A clean burning and correctly adjusted pilot light is necessary for your water heater to function at peak efficiency. The color of the flame of the pilot light ought to be blue with natural gas heaters or blue/green with just a bit of yellow at the tip with propane heaters. A short flame, a yellow flame, or a flame with a divided flame at the top implies that a modification is necessary.

Just For Electric Water Heaters

Utilizing insulation wraps or covers around the storage tank can certainly help maintain a regular temperature inside of the storage tank without the need for as much electrical power. Additionally, with the heater not needing to perform as often will increase the life span of the heating element as it will not be put to use as much. Every 3 months roughly, look at to verify the insulation wrap is attached nicely and hasn’t fallen or shifted on the water storage tank.

Routine evaluation of the heating element is crucial and definitely will help decrease the need for an unexpected repair. We aren’t going to get into the specifics for a total assessment right here, however one will require a voltage/OHM meter to assure there does exist a closed electrical circuit. Heating elements will need updating from time to time.

Continue to keep the place close to ones water heater thoroughly clean of dirt. Notably if the water heater is positioned in the garage area, be certain to keep the vicinity swept. The cleaner the heater is, the considerably better it is going to work without having the necessity of a water heater repair.

Replace Old Water Heaters With Energy Efficient Ones

Today, nearly all water heaters made have a very fine volume of energy efficiency. In April of 2015, new codes were started in the United States on water heaters. Clearly, the better quality the heater, the longer the life one could possibly get from the device while using ideal servicing over time. Don’t wait to phone Hot Water Heater Repair Carrollton TX to talk about water heater maintenance or even to help answer any concerns on deciding on the most proper replacement water heater for ones house or workplace. Brand, model, and size should all be considered throughout the selection process and not simply implement the “bigger the better” saying. With regard to storage tank water heaters, one doesn’t need to be always maintaining a surplus quantity of heated up water that won’t be used.

Water Heater CO2 Poisoning Prevention

Posted by on May 21, 2015 in Gas Water Heater Repair Carrollton TX, Tankless Water Heater Repair Carrollton TX, Water Heater Repair Carrollton TX, Water Heater Replacement Carrollton TX, Water Heater Safety | 0 comments

Today Water Heater Repair Carrollton TX is going to look at the dark side of water heaters. Although a rather maintenance free home appliance, there are 2 sizable potential issues one ought to perform safety with to make certain everybody in the house is protected. The first risk is of a water heater explosion, and the next, that is our theme in this article, is carbon monoxide poisoning. Any nonrenewable fuel burning device creates this lethal gas, including water heaters, but this danger can be managed very easily. Let’s take a look at first, the factors and sources of carbon monoxide poisoning, and then the symptoms, and finally the way to take care of ones property.

Reasons for Carbon Monoxide Poisoning

By definition, carbon monoxide gas (CO) is a colorless, odor-free gas that is a bi-product of the burning of a nonrenewable fuel source such as wood, gasoline, coal, natural gas, or kerosene. Inhaling carbon monoxide gas fumes not only avoids oxygen from being made use of appropriately by the body, however likewise triggers damage to the central nervous system. Individuals with existing wellness issues such as heart and lung condition are specifically susceptible, as are babies, youngsters, pregnant women, and seniors.

Sources of Carbon Monoxide Gas

The wintertime heating period is when the vast majority of carbon monoxide gas direct exposures take place as a consequence of using unvented supplemental heaters. An unvented additional heater is a sort of space heater that makes use of inside air for heating and vents the gases created in the heating procedure out into the house. A lot of heaters of this kind use kerosene or natural gas for fuel. While more recent designs have oxygen sensing units that shut down the heater when the oxygen level in the area falls below a particular level, older designs do not have such safety functions. Because of these security troubles, unvented space heaters have actually been prohibited in numerous states. Other causes of carbon monoxide gas are from not working cooking devices, cigarette smoke, obstructed chimneys, automobile exhaust, not working furnaces and gas clothing dryers, wood burning fireplaces, and, as we know already, a water heater.

Signs of Carbon Monoxide Gas Poisoning

The signs and symptoms of carbon monoxide poisoning are not necessarily the very same from patient to patient and they are comparable to different sorts of health problem, like the flu or food poisoning. The subsequent list are the most usual signs, however a doctor ought to be contacted if one is not sure that carbon monoxide gas is the origin of the symptom.Hot Water Heater Repair Carrollton TX

headache
dizziness
weakness
queasiness and throwing up
rapid heart beat
seizures
loss of consciousness or coma
respiratory failure
cardiac arrest
loss of hearing
fuzzy vision
disorientation

Carbon Monoxide Poisoning Deterrence From a Water Heater

The very first deterrent is to ensure that the water heater has been correctly setup by a specialist. Next, routine upkeep is required as is a functioning CO2 detector in the house.

Defense By Correct Gas Appliance Ventilation

The CDC provides the following details on avoiding CO2 poisoning by seeing to it ones home appliances are vented properly.

  • All gas appliances must be vented so that CO will not build up in your home, cabin, or camper.
  • Never burn anything in a stove or fireplace that isn’t vented.
  • Have your chimney checked or cleaned every year. Chimneys can be blocked by debris. This can cause CO to build up inside your home or cabin.
  • Never patch a vent pipe with tape, gum, or something else. This kind of patch can make CO build up in your home, cabin, or camper.
  • Horizontal vent pipes to fuel appliances should not be perfectly level. Indoor vent pipes should go up slightly as they go toward outdoors. This helps prevent CO or other gases from leaking if the joints or pipes aren’t fitted tightly.  (read more…)

It is absolutely crucial to have CO2 detectors in the house. The Colorado State University Extension provides the following pointers when picking a CO2 alarm.

  • Some inexpensive alarms consist of a card with a spot (spot detectors) that changes color in the presence of CO. The absence of an audible signal does not meet UL or IAS requirements for alarms, so these devices do not provide adequate warning of CO.
  • Some CO alarms have a sensor that must be replaced every year or so. The expense of this part should be a factor in purchase decisions.
  • Battery-operated alarms are portable and will function during a power failure, which is when emergency heating might be used. Batteries must be replaced, although some alarms have long-life batteries that will last up to five years.
  • Line-powered alarms (110 volt) require electrical outlets but do not need batteries. They will not function during a power failure. Some line-powered alarms have battery backups.
  • Some alarms have digital readouts indicating CO levels. Alarms with memories can help document and correct CO problems.  (read more…)

The following video offers some good security suggestions for water heaters.

Not to frighten anybody, however we likewise wished to include the following video of a water heater set up that is not working properly and is harmful.

Please see a medical professional promptly if one presumes that carbon monoxide gas poisoning is a problem. Water Heater Repair Carrollton cannot stress enough the requirement of ensuring that all water heater maintenance and installs are carried out by a specialist.

Repairing a Noisy Water Heater

Posted by on Mar 17, 2015 in Gas Water Heater Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

Water Heater Repair Carrollton TX is regularly being consulted to check out at water heater. Popping and knocking noises can be a result of problems with the water heater, but it’s likewise an aggravation. We are going to go over the most typical reason your water heater may possibly begin generating noise and what you can possibly do to calm it down! Prior to consulting a Carrollton  professional, have a look at one of the most popular water heater troubles and remedies.

The most likely reason a water heater can make noise

Again, if the sound is an indicator of issues with the heater that difficulty is most probably sediment build up. The sediment arises from the water in the storage tank. It is essentially made of calcium and magnesium debris and is mainly a situation in residences which may have hard water.

If the sediment starts to accumulate at the bottom of the storage tank, it traps a little part of hot water under it. This triggers the hot water to boil as the tank functions. The sounds noticed are the bubbles popping through the sediment.

Furthermore, the sediment itself may very well be the factor for the sounds. The sediment sits at the bottom of the tank and can get burnt up producing unexpected sounds. And at times, the sediment will get carried up to the top of the tank and breaks off producing sounds as it plunges back down, bumping the sides on its way.

How to avoid a water heater from generating noise

If sediment build-up is what’s producing the sounds, the heater should be examined. Water Heater Repair Carrollton can accomplish this and provide the tank a flush or advise a different remedy.

You can also hinder sediment build-up by having expert routine maintenance done on the storage tank at minimum annually. This system involves flushing the tank of any sediment.

An additional terrific approach is to add a water softener in your Carrollton property. Water softeners take out minerals from the water prior to it entering the water heater, dramatically lowering sediment build up.

For more info about other probable problems and remedies provide Hot Water Heater Repair Carrollton TX a phone call!

Motives Why a Hot Water Tank Will Explode

Posted by on Jan 22, 2015 in Gas Water Heater Repair Carrollton TX, Water Heater Repair Carrollton TX, Water Heater Safety | 0 comments

With regards to needing to perform servicing on ones water heater, it is a relatively minimal maintenance home appliance.  Nevertheless, one important aspect of it ought to be checked out routinely.  Water Heater Repair Carrollton TX would like to pass on this safety material regarding ones water heater today.

Extreme temperature if coupled with tank deterioration inside the storage tank could cause an explosion. Any time the water temperature is less than 212 degrees Fahrenheit, one is going to be secure from an explosion, though there is a threat of scalding at that temperature.  However, if the water temperature is over 212 degrees, water changes into steam, which will enlarge to 1,700 times the space it takes up as water. This is the time an explosion can happen.

Cautionary Signals of a Water Heater ExplosionHot Water Heater Repair Carrollton

The leading sign is if one goes to get hot water from a faucet and only steam comes out.  Without delay shut off electric power if one owns an electric water heater.  If one owns a gas hot water heater, shut off the gas valve on the water heater.  Next, give us a call to come examine the condition.

Minimizing Potential Water Heater Dangers

The most significant upkeep endeavor having a water heater is to check the pressure relief valve, also referred to as the T&P valve, on a standard schedule.   This valve helps manage the pressure accumulation on the interior of the water storage tank to avoid a hazardous increase in temperature and overpressure.

Caution!
Be careful, the water release with a T&P valve is often rather hot. If you do not feel at ease examining the valve inform us.  Additionally, performing any sort of fixes to the valve should really be completed by a specialized plumbing repair business.

How to Test the T&P Valve

Clear the space close to the overflow pipe and floor drain.
Raise the test handle for about 5 seconds or until the water runs clean.
Let go of the handle.
If the T&P valve keeps on running with water, lift up the handle up and down rapidly to have it reseat itself.  One might have to do this a handful of times.  IF it has not been tested for a while, it might be difficult to raise it at first.  Avoid using an excessive amount of force, however might need to utilize just a little.
If the T&P valve continues to leak, it should really be changed.

Some other items to watch out for are deterioration on the stem of the valve.  If there is any water dripping out of the valve stem or out of the drain valve.

Interested in far more suggestions?  Look at Water Heater Repair Carrollton’s additional articles right here:

Carrollton Water Heating Savings Advice

Heat Loss Prevention With Water Heater Blankets

From around the Web:

The Aquanta smart water-heater controller promises to slash your energy bill

Home maintenance checklist: Fall

Leaking Carrollton Water Heater Pressure Relief Valve

Posted by on Dec 9, 2014 in Gas Water Heater Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

The pressure relief valve of a water heater has a vital job – seeing to it the water heater tank does not blow up. So with that in mind, Water Heater Repair Carrollton wants to ensure property owners know the best ways to best care for it. They will leak when the valve wears out or when the water storage tank pressure gets higher then the relief point.Hot Water Heater Repair Carrollton TX

We recommend that at least twice a year, homeowners test to make sure the pressure relief valve, or T&P valve as we will call it, is working correctly. All one has to do is raise the handle for a few seconds and release it. It should snap back to its initial position. When it is lifted, one might hear the noise of pressure being released from it, much like the sound of air coming out of a tire pump when being disconnected. Likewise, a little water may come out also. Both are regular. If the valve has not been tested in a long time, it may stick at first too.

However, if the handle doesn’t snap back, or if it remains to leak a little water, that is not regular. If it still leaks some, raise the handle a couple of more times to see if it will re-seat itself. You could want to wait a day or so it see if it re-seats itself prior to assuming it needs to be replaced.

Hot Water Heater Repair Carrollton would like to handle any T&P valve replacements for you, so though water heaters are normally relatively upkeep free, there are some safety preventative measures one must bear in mind. With that here is an overview of a pressure relief valve replacement.

1. The gas to the water heater needs to be shut off, or the breaker for an electrical water heater.
2. The cold water cut-off valve has to be closed next.
3. The valve below the T&P valve needs to be opened to drain some water in order to relieve some of the pressure in the storage tank.
4. The overflow pipe of the T&P valve needs to be taken off. It may need to be cut off if it is soldered or firmly glued.
5. The pressure relief valve has to be unscrewed with a pipe wrench.
6. Wrap the brand-new T&P valve with Teflon tape and screw it back in place. See to it the overflow pipe opening is placed away from the storage tank.
7. Reattach the drain pipe, likewise using brand-new Teflon tape.
8. Turn the water back on, and examine your work for any leakages.

The following video offers an overview of this process:


Carrollton Water Heating Savings Advice

Posted by on Nov 7, 2014 in Water Heater Repair Carrollton TX, Water Heating Savings | 0 comments

Faucet aerators and low flow shower heads help to conserve water, and water conservation suggests home energy savings for you.

Bathroom and kitchen faucet aerators are easy to add to ones faucets. The wire screens just screw in and will blend air into the water flow, think of it as rationing the water coming out of the faucet.Water Heater Repair Carrollton TX

When first introduced the initial purpose was to just minimize the flow rate or water stream in order to remove sink splashing.

However, with the increasing interest in water preservation, house owners and companies that are looking to save on energy usage, are becoming more thoughtful about the water saving potential of faucet aerators.

In terms of ones Carrollton water heater, aerators don’t simply conserve water, they also help in reducing the gas and electrical energy expense of water heating. Aerators paired with water saving shower heads can reduce the typical houses hot water use by as much as 50 percent.

Both water saving devices are unbelievably low-cost and really simple for homeowners to set up.

Low flow aerators can be put on just about any standard faucet. Look along the tips of ones faucets to see if there are threads along the inside. Even lots of older bathroom and kitchen sink faucets are pre-threaded.

If one already has older aerators installed, they can be removed by hand or with a wrench. The flow rate (which is measured in gallons per minute or gpm) should be inscribed along the side. Newer faucet aerators can substantially lowered flow rates even additionally than older designs and all without minimizing the water pressure.

Kitchen Aerators

Kitchen sink faucets typically require higher flow rates than a restroom faucet. Because of this, aerators with minimum flow rate of 1.5 gpm is extremely advised for conserving water. Nevertheless kitchen sink faucets without aerators can utilize as much as 3 to 5 gallons of water per minute.

A new design of aerators have swivel pivots that enable a circular or rotating movement which comes in helpful when cleaning ones kitchen sink. Those who clean dishes by hand may find a swivel aerator with a shut off valve even more ideal.

Bathroom Aerators

Bathroom aerators normally are chrome plated or brass. They provide a more direct and pressurized spray than a lot of kitchen sink aerators. And bathroom aerators normally cost even less, varying anywhere from $2 to $5 each.

Bathroom faucets without these attachments can make use of anywhere from 2 to 4 gallons of water per minute. New low flow bathroom aerators utilize just 1 to.5 gallons per minute and all without lowering water pressure.

Remember to Keep Aerators Clean

The wire screens can get clogged with sediments and other mineral deposits after months or years of continuous use. Periodically remove for a cleaning. This will certainly fix possible water pressure troubles along with avoid future faucet leakages.

Low Flow Shower Heads

Setting up low flow shower heads is genuinely among the most cost effective things any house owner can do to save water. 30 % to 40 % of American houses today have conventional bathroom shower heads installed which utilize as much as 5 to 7 gallons of water per minute.

The low flow shower heads currently on the marketplace are not the old flow restricting designs of the past. A brand-new water conserving shower head can substantially minimize ones water utilize and enhance water pressure at the same time.

Now water saver shower heads make use of air chambers or jet streams to rapidly mix air into the water flow. The streams and chambers allow the shower heads to use substantially less water, as well as enhance water pressure for that unwinding massage sensation.

More recently some models have effectively lowered water flow rates even lower than the federal guidelines. Some low flow designs utilize as low as 1 gallon of water per minute.

A few of the very best shower heads allow one to stop briefly warm water while in the shower. These shower heads are extremely convenient and they can assist one save even more by utilizing less warm and warm water while bathing.

This gives ones hot water heater a much needed break, which in return translates into lower water heating cost.

Check out Water Heater Repair Carrollton TX’s other tips in our blog here too!

Carrollton Water Heater Installation Costs

Posted by on Nov 6, 2014 in Water Heater Replacement Carrollton TX | 0 comments

The typical life-span of a standard tank-style gas water heater or electric water heater is about eight to 12 years, so the prospect of needing to change a water heater is a common home improvement. Water Heater Repair Carrollton TX has written a few of the elements that affect the installation costs here.

The expenses to install a brand-new Carrollton hot water heater do vary in cost depending on the business performing the installation, and depending on the type of water heater set up. For instance, energy-efficient tankless water heaters do cost more to set up, though those expenses can be recouped over the life of the device. Check out this tool from homewyse.com that will provide a quote on water heater setup costs for the part of the nation one lives in.

Water Heater Installation Cost Factors

Without seeing the area that ones water heater will be installed or replaced, it is tough to offer a particular idea of the cost. If it is a water heater replacement, and is being replaced with a comparable sized and design of heater, the installation expenses will certainly be really reasonable. If one is changing to a different type of water heater, like from an electric to a gas or tankless unit, the setup costs will be higher due to the fact that we will need to potentially install gas lines and connections.

Another factor to consider is to make sure a replacement water heater will be up to code with exactly what is required now, not with what the code was 10 to twelve years earlier when the present water heater was set up. Also, there is the potential that the present water heater was not up to code when it was initially set up either! Which can be the case if a previous property owner did the installation him or herself.

Because of the safety elements involved with water heaters, it is always best to have a professional plumbing business perform the setup. One, the majority of house owners will not have a good idea of exactly what the code standards are. One danger aspect is that electric water heaters make use of 240 volts of electrical power, which is extremely hazardous to handle if not experienced in doing this. Hot Water Heater Repair Carrollton spends a lot of time repairing incorrectly installed water heaters.

Another safety concern with not having a professional set up ones water heater is working with gas lines. This, too, can be harmful, and a scenario where there can not be any leaks.

A last safety issue is with correctly venting the exhaust to ensure carbon monoxide gas goes out of the house. Carbon monoxide poisoning takes place more regularly than many people believe, and it is best to make sure one has a carbon monoxide detector in ones house too. According to the Centers for Disease Control, unintended carbon monoxide poisoning triggers 400 deaths each year and 20,000 visits to the emergency room.

Other considerations with setting up is making sure it is plumbed properly, there is enough clearance and guaranteeing drip pans are geared up, if needed.

Heat Loss Prevention With Water Heater Blankets

Posted by on Nov 1, 2014 in Water Heater Repair Carrollton TX | 0 comments

Water heating unit wraps or blankets are probably the most cost effective measure out of all the energy conservation measures. There are no other preservation measures that has the life span, cost and and repayment that the water heating unit wraps have suggests Water Heater Repair Carrollton TX.

These insulation coats last as long as the water heating unit and if you are as penny-wise, you can utilize the old one and put it on the new one, if it will certainly fit. Typical life of a water heating unit, 10 years. Expense $30. Saving differs from $30 to $50 per year, relying on the performance of the water heating unit.Water Heater Repair Carrollton TX

What water heating unit wraps do is preserve the temperature of the water longer. Simply puts, the heating elements or gas do not need to begin as commonly when a insulation jacket is set up. Besides the truth that it saves you cash on your energy costs, it will, without question, lengthen the life of the water heating unit. To illustrate this is you and your neighbor work at the same area, 10 miles away. With all else being equal other than that you drive to work at 25 mph and he/she does it at 40 miles per hour. He/she gets to work or home in 11 minutes and it takes you 12 minutes. As far as the cars are worried, which vehicle will utilize more gas for the exact same range? Which vehicle will require more upkeep? Which vehicle will last longer?

This applies to a water heating unit in much the same means. The average home in fact only uses hot water a bit more than a hour. As an example, it may take you 45 minutes to wash garments, but it just takes 2 minutes for the washer to full of warm water. Your children could take 45 minute showers, they are just utilizing the water in the shower at most 15 minutes. Try staying under a hot shower for more than 15 minutes, you will come out looking like a trim. What this implies is that for more than 22 hours a day, the water heating unit simply keeps the temperature level of the water. So let’s say you are extreme with hot water, let’s double it, it is still more than 20 hours a day simply preserving the temperature. Plainly the substantial bulk of the expense to run a water heating system is preserving the temperature of the water when no-one is making use of hot water.

A water heater without the insulation jacket comes on to keep the temperature level about 4 times an hour. One with the insulation coat 3 times an hour. On top of that the water heating system without the coat will certainly stay on for a longer period than one with the jacket. Given that all heating elements create hostile environments, regardless if it is electric or gas, the more times per hour and the longer the heating elements remain on, the shorter the life expectancy of the water heating unit. You will take advantage of the installation of the insulation jacket but who will not benefit are the people who install them for a living and the producers. Let us know at Water Heater Repair Carrollton TX if you need assistance with sizing or choosing the best one for your home.

Here is another video on how to install a water heater blanket:

Holiday Carrollton Plumbing Advice

Posted by on Oct 29, 2014 in Plumbing Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

The holiday season is one of the busiest times of the year for us, especially with drain cleaning, toilet repairs and other plumbing repairs. with the increased amount of guests and family in ones home, it can take a toll on the plumbing system.

Carrollton hot water heaters are working overtime with the included variety of showers start taken, clothing being cleaned, and dishes being washed or gone through the dishwasher. We advise waiting a few minutes between showers if several are to be taken right after each other. The same goes with picking times to use the dishwasher and washing machine as well.

Drains specifically have it hard, for we are carrying out Carrollton drain cleaning much more regularly, with the added amount of individuals making use of ones plumbing. It is likewise a fascinating time to see how many toys and things that kids accidentally try flushing down the toilet too!

Below is an infographic that will certainly provide some tips on ways to manage ones water heating and plumbing this holiday season.

Water Heater Repair Carrollton TX

What is the Perfect Carrollton Water Heater Temperature

Posted by on Sep 30, 2014 in Water Heater Repair Carrollton TX | 0 comments

There are different views on exactly what is the very best temperature level at which to set ones water heater. Water Heater Repair Carrollton will be sharing some of the different views with specific evidence from those sources in order for one to make his or her own choice on the topic.

First off, the default setting most water heater producers have their tanks set at is 140 degrees. If you have never checked this already on your Carrollton water heater, that might be the temperature it is set. Likewise, it can be difficult to understand for sure exactly what the temperature setting is due to the fact that often times the temperature level dial does not have actual degrees printed on it, simply warm, hot, really hot … something to that effect. Some people feel they are pre-set at a high temperature level so it feels outstanding to have a lot of hot water – type of like attempting to produce excellent brand awareness in consumers.

In regards to energy savings, by turning a water heater down from 140 to 120 degrees, it will save in between 6 to 10 percent of total energy used. That equates to between $6 to $20 a year in many cases.

Let’s begin with the most likely the most renowned source, the U.S. Department of Energy. They suggest a setting of 120 degrees. The link to their website above provides lots of excellent details on the best ways to minimize ones hot water consumption and costs. It is definitely worth a read.

Now for the health dangers of too low of a temperature level setting. It can be concluded that Legionella bacteria has the ideal development range between 68 to 122 degrees. It is thought that 25 percent of all water heaters have differing levels of Legionella bacteria contamination.

Legionella bacteria causes a form of pneumonia and is passed to humans when one inhales water contaminated with the bacteria – generally in showers, whirlpool baths and even air conditioning systems. Consuming the water is usually ok. It is a concern with having the bacteria get in ones lungs.

The Centers for Disease Control and Prevention estimates 8,000 to 18,000 Americans contract the condition every year. Five to 30 percent of the cases are deadly.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)

Cases to not have the water heater temperature set at 140 degrees would be if there are children in your home or potentially with elderly people too. The risk of being burnt if the faucet was completely on hot water can be too great. Clearly, any individual living in the home that is at threat of contracting Legionella Disease need to have it set at 140.

Summary

So choose if there are any issues of individuals burning themselves if the water temperature is too hot. Also, be conscious of any individual who has issues of contracting Legionella Disease. Since the annual expense savings of turning the temperature level down is only about $20 many the time with the average home’s hot water use, it could be a good option to keep the temperature level above 120 degrees just for the wellness related advantages; nevertheless, Hot Water Heater Repair Carrollton TX will let you make the call.

The following infographic summarizes this conversation:

Water Heater Repair Carrollton

Preventative Water Heater Maintenance in 10 Minutes

Posted by on Sep 24, 2014 in Water Heater Repair Carrollton TX | 0 comments

Water heater maintenance in 10 minutes? Yep, that’s true. Water Heater Repair Carrollton TX is going to explain how to do some water heater preventative maintenance. And, that is the amount of time it will take to do these two important water heater maintenance jobs; however, we understand that these will do an excellent job of assisting with 3 things:

  • Having ones water heater last as long as possible for it will save on money with using it.
  • Making sure a water heater runs safely is critical for we do not want it to explode in in ones house.
  • And having it run as energy efficiently as possible also helps one save one some cash.

We are now all set to invest 10 minutes once or two times a year to assist in saving some money on energy costs.

Testing the T&P Relief Valve
The T&P Valve, also called the temperature and pressure relief valve, has an essential job. It’s job is to help see to it excess pressure inside the water storage tank does not build up, or in even more basic terms, it makes sure that a water heater does not blow up. The T&P valve is the part that has a lever or little handle. Just raise it part way and afterwards release it back. Hopefully, it snaps back to its shut position rapidly. A little water should be heard going into the drain pipe below the lever that was just lifted and perhaps heard some pressure being released also. If none of these things have taken place throughout the test, the valve will have to be changed.

Carry out a Mini Water Heater Tank Flush
Naturally, rust and rust will take place inside the water tank thanks to the chemical reactions taking place with all the elements inside that are required to heat up water. We will not get overly technical right here, but it is easy to help avoid this process by doing a flush or draining of all or some of the water in the storage tank.

For just a small flush, position a container under the drain valve below the tank. Open the drain valve and fill the container with water. Drain a minimum of a few gallons of water in total. Let the water sit in the pail for a couple of minutes to settle and analyze if there is much that settles to the bottom of the pail. If there is, if the water heater has not been drained for a very long time (or ever), it would be best to do a full flush of the tank to get as much of the sediment out as possible. You will want to turn the temperature level dial down and may want to let the water cool down for about an hour initially so it is not too hot while draining it. Likewise, it would be easier to attach a hose to the drain valve and let the water go outside instead of utilizing buckets.

If the water looks fairly clean and clear from the tiny test you should be all set. When the water heater has an excessive amount of sediment inside of it, it can make loud popping noises and it minimizes its effectiveness too.

Though water heaters are fairly upkeep free and uncomplicated to run, whenever one feels the smallest awkward or are unsure of exactly what to do, it is always best to have give Water Heater Repair Carrollton a call to assist with ones regular water heater maintenance.

Here is an infographic that illustrates these steps, and check out our blog more water heater tips and advice.

Water Heater Repair Carrollton TX

Carrollton Water Heater Safety Precautions

Posted by on Sep 20, 2014 in Plumbing Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

Properly preserving ones water heater is essential not just so it works to its full potential and can save some energy cash, but for safety concerns too. Yes, it can blow up – it does not take place too commonly for residents, however obviously this is something that Water Heater Repair Carrollton TX does not desire to have happen to you!

Vents
Venting can be kind of technical but we will review the basics here. The vent need to be the same diameter as the draft diverter of the water heater tank. It is supposed to go up and out (for atmospherically vented heaters). Not various other directs like up, down, up and out. For direct-vent water heaters, the vent should go out a side wall. When it comes to power-vent heaters, the fan blows the fumes out, so there is some flexibility in the instructions they are vented.

Any roof or wall that the vent goes through should be a double wall. The single wall pass throughs should be screwed with three screws per area. If these basics are not abided by, the vents can fall apart over time and carbon monoxide gas can cause major problems within ones home. Naturally we don’t desire that to happen!

The only other interested in venting is that of backdrafting. The fumes can consume the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a good scenario for a correctly working water heater. If the fumes go back inside the rather of being effectively vented outside, the fumes can get in the living areas of the house. Soot problems can occur also.

Dielectric Connectors
The steel water heater is connected to cooper pipes by the dielectric connectors. When two these 2 metals are put together in water electrolysis occurs. The process corrodes one metal away to shield the other. This process is crucial in securing the inside of the water heater. Assessment for leaks need to be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a fundamental part of the water heater, for it helps see to it the darn thing does not explode under pressure if the temperature goes beyond the right limits the water heater is developed for. Once a year (a minimum of) the T&P valve ought to be checked to ensure, it is working correctly, for they can be prone to failure. Merely pulling up on the handle water ought to stream easily out and stop when the handle is let go of. If it simply runs or trickles, or does absolutely nothing at all, it will need to be replaced.

The drain lines for the T&P line ought to not be directed up, because water does not flow uphill too well. Make certain it goes downhill and or out please. If water is running out the drain line routinely, it is the indication of something incorrect too. It can be one of a number of different things that we will not enter here – simply speak to a regional plumber please.

Earthquake Straps
Yep, even if you don’t reside in an earthquake area and are needed to have these on ones water heater, it is a good concept to do so. It appears like the majority of all new houses in sub-divisions these days have the water heater in the garage. Yes, there is generally a concrete curb in front of it so one does not drive a vehicle into it, however things can accidentally knock it over so be safe and strap that thank in.

Temperature Setting
It appears most domestic water heater tanks have settings of warm – hot – really hot … and not degree settings. Some “ideas” on conserving energy in the house specifically in the winter season time, say to lower the setting on the tank to 120 degrees. That’s wonderful for conserving energy but legionella germs, which triggers Legionnaire’s condition can grow at 120 degrees. By breathing in the mist from the water in the shower, one can breathe in the germs. Attempt to discover a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature level so be cautious.

Anode Rods
These generally are made of aluminum and there is nothing incorrect with that in concept, though Water Heater Repair Carrollton suggests using magnesium ones. Let’s state for whatever reason there is some type of emergency or catastrophe where one lives and one had to utilize the water in the water heater for drinking water (due to the fact that lots of emergency readiness individuals encourage doing this). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum substances, which is bad for the human body. It is bad for the stomach, intestinal tract and joints.

The anodes assist with rust protection and are important in extending the life of the water heater. They can also aid with smell issues with the water. Overall, magnesium anodes just work much better for lots of various reasons like the wellness perks, let construct up of sediment, a quieter water heater, and they often work better with softened water.

Drain Valve
Ok, simply inspect it a minimum of yearly to ensure the darn thing opens and works. And it is good to drain and flush the tank at least once a year anyway (something you obviously are doing currently). If for some reason one needs to use the water throughout a catastrophe or drain it to quite a noisy tank and have not drained it routinely, and it doesn’t open, it will take longer to remedy the trouble you are at first attempting to deal with.

Combustion Changer Hatch
Given that gas and oil water heaters breathe the air drawn in from beneath, combust with it and exhale it, it is crucial to keep the area around it, specially underneath the water heater, clean and swept. If if is not burning effectively, it can trigger drafting concerns (mentioned above), as well as combustion and fume issues and possibly be a fire hazard. A few of examining the chamber and exactly how the flame burns is objective so we are not going to enter into a lot of detail below. it is essential to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not a pretty good indication at all. One ought to see some blue flame at the bottom when it burns and orange and yellow at the top, nevertheless, the yellow should not be very high up. One should see grey metal, some white condensation marks are ok.

Here is an infographic to highlight the information above:

Water Heater Repair Carrollton TX

 

Check out our article An Overview of 4 Plumbing Troubles next…

An Overview of 4 Plumbing Troubles

Posted by on Jun 19, 2014 in Plumbing Repair Carrollton TX | 0 comments

We are able to assist with any Plumbing Repair Carrollton TX issue one be having.  Nevertheless, it’s also a great idea to make certain you have the skills to handle any smaller sized plumbing issues that may occur throughout a time when it can be even harder to get an expert to ones house. Right here are 5 basic plumbing fixes one may simply have the ability to look after oneself.

Broken Pipes

Water Heater Repair Carrollton TX

A broken pipe can cause many people to be over anxious, but take a deep breath before discovering the main water pipe and switching the supply off, one can well find oneself much less stressed. Now in this case, one will certainly have to get a plumbing professional out to resolve the actual problem.

Blocked Toilet

Frequently this is as easy a job as buying a cheap plunger and getting busy with it in the u-bend. If one finds the plunger isn’t enough to shift the blockage away, there are other choices. Plumbing wire will permit you to get right in where the plunger can not go and loosen what needs to be moved, while a drain snake will offer one a more detailed clearing choice too.

Leaking Faucets

Easily among the most typical plumbing problems homeowners will face, but one that is usually as basic as changing an old washer. First of all, switch off the water at the mains, then, holding the spout of the faucet, unscrew the nut that holds it in place. Next, get rid of the washer, pop on the new one and make certain you secure the bolt firmly. You need to discover in many cases this suffices to fix the problem.

Clogged up Sinks

Whether it is the restroom or the kitchen, it’s extremely easy for a sink to become congested. If it’s the former, it’ll likely be as simple as getting rid of hair, however in the latter, food can make its method into the pipes and trigger an actual problem. Just like toilets, a plunger or plumbing wire will typically sort it, however one could also want to get under the sink and get rid of the pipe. Just be careful to clear the area as it could get a bit damp when one does.

Home emergency plumbing repair situation coverage is always a great idea for the bigger things, but a little preparation could be all you need for a few of the smaller sized tasks around your home.

Carrollton Home Spring Maintenance Tasks

Posted by on May 12, 2014 in Plumbing Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

Here are a couple of different upkeep jobs to perform around our home in the spring from Water Heater Repair Carrollton TX. Many of these tasks will not take long to do and will help quite a bit in protecting the value of ones home, along with making it more energy effective.

Water HeaterWater Heater Repair Carrollton TX
The typical life of a water heater is from 8 to twelve years. It’s recommended to check to see if there is any leaking or rusting at the device’s base, and if there are any leaks due to rust, it is a good indication that the water heater should be replaced unfortunately. In areas with hard water, it could be needed to drain the water heater to get rid of sediment accumulation in the tank. This must be done two times a year to keep the heater working effectively. It also helps make it run quieter too!

Plumbing
With leaking faucets, replace washers as required, even if your feline enjoys to sit in the tub and leisurely lick the leakage. And do not forget to check for under-sink and dishwasher leakages– and repair as necessary. While it’s springtime and not hot enough for you to sweat doing these tasks– see to it your pipes are not either. In addition ensure your drains are running easily and your washing equipment hoses are not bulging, cracked, or damp.

Outdoor Faucets
If you have drained and switched off outside faucets for winter, turn them back on and prime if needed. Inspect for leaks around turn-off valves.

Refrigerators
Your refrigerator is one of the greatest electrical energy eaters in the house– so making sure that your door seals are airtight is very important. To check this, close the door over a dollar expense and if you can quickly draw it out, the door latch might need readjustment or the seal could need changing. Believe it or not, a tiny bit of air leakage can result in greater energy expenses. And it’s also an excellent time to clean the back coils as that’s another reason for inefficiency. Now go stock up on food, treat yourself, as a full fridge and freezer utilizes less energy than an empty one.

Storm Windows and Screens
The drastic changes in temperature in between winter season and spring can damage caulking or rubber seals around your home’s windows and outside doors. Take time and look– it’s an easy repair and your energy expenses will show the time invested. If you have removable storm windows– take them off, clean, and store them and replace with screens. And don’t forget to patch holes in door and window screens– to keep out mosquitoes and various other tiny biters.

A/C Units
Check portable AC systems to make sure they are working and filters are cleaned– warm weather condition will come faster than you think. An air conditioning unit not just cools you down, but an efficient air conditioning unit decreases wetness and humidity from the house, which can actually harm the foundation if left uncontrolled. Get in the practice of altering or cleaning the filters of both a central system and portable devices once a month as dust and dirt lowers effectiveness. Central AC systems require that the hose connections are not leaking and the drain pans are draining properly– so examine those. If a condensate drain hose becomes clogged, it could be a buildup of algae. If this is the case, make use of a wet-vac to suck out any blockage. And while you’re at it, clear out the ducts likewise.

 

 

Water Heater Repair Carrollton Video Overview

Posted by on May 3, 2014 in Plumbing Repair Carrollton TX, Water Heater Repair Carrollton TX | 0 comments

Below is a copy of our newest company video overview for Water Heater Repair Carrollton TX we wish to share with you today. Besides fixing broken water heaters, we are a complete service plumbing repair business too. We can take care of any residential or commercial repair, service, installation, and replacement plumbing scenario that has to be tended to.

If you ever experience any sounds coming from you water heater, bad odors from the water, or any wetness or leakages around it, don’t wait to give us a call! These are indicators that water heater maintenance is needed, which will avoid bigger troubles down the road. Water heaters are generally upkeep free compared to other home appliances, however in order to get the most out of the unit and to have the heater run as efficiently as possible, regular maintenance is required.